[markmitch]

I need both bumper brackets that are on the far right and far left of the rear bumper. They bolt to the unibody and to the inside corners of the rear bumper. Let me know the price and shipping to 03825, Barrington, NH. Thank you, Mark

 

[VannyD]

I would like the inner fender splash guards...all of them? That rear door seal too.

Chris in NY.

 

[M_a_t_t]

I need both bumper brackets that are on the far right and far left of the rear bumper. They bolt to the unibody and to the inside corners of the rear bumper. Let me know the price and shipping to 03825, Barrington, NH. Thank you, Mark

I sent a message with some pictures.

I would like the inner fender splash guards...all of them? That rear door seal too.

Chris in NY.

The driver side is ripped in half. The passenger side looks like it has a small tear in it. I will have to remove the wheel to get a good picture of it. I need to look at the door seals on my 86 before I offer those. You know they are barn doors not dutch doors right?

 

[Rod's Trucks]

I would like the inner fender splash guards...all of them? That rear door seal too.

Chris in NY.

Be aware, the AWD and 2WD inner fender splash guards are a different pattern.
Rod J

 

[VannyD]

I sent a message with some pictures.


The driver side is ripped in half. The passenger side looks like it has a small tear in it. I will have to remove the wheel to get a good picture of it. I need to look at the door seals on my 86 before I offer those. You know they are barn doors not dutch doors right?

Matt, You still have that rear barn door seal from the red parts van? -Chris

 

[M_a_t_t]

Matt, You still have that rear barn door seal from the red parts van? -Chris

The left door stopped opening. I'll take a better look at the seal by Friday and pm some pictures if it's worth passing on.

 

[VannyD]

The left door stopped opening. I'll take a better look at the seal by Friday and pm some pictures if it's worth passing on.

If I'm not mistaken the seal is on the right side....at least the seal I'm interested in. It's the big one, like 2-3 inches wide at places.

 

[M_a_t_t]

Are you talking about the seal on the door of the van? I hadn't looked at it too hard and assumed it was like the dutch door seal just longer. This one has a ~5 inch chunk missing in the bottom outside corner (corner closest to the hinge).

 

[WVOutdoors]

I'm VERY interested in the lower fender molding caps if they are not melted. I need right and left. Not full molding, just the caps like in this picture:

 

[92Astro]

Hi there, I'm looking for the transfer case upper support brace? I have 92. I Think its the same 90-95. Its shown in diagram (47).
Please let me know.

 

[M_a_t_t]

Hi there, I'm looking for the transfer case upper support brace? I have 92. I Think its the same 90-95. Its shown in diagram (47).
Please let me know. View attachment 285845

It's a 2wd van so it doesn't have that.

 

[92Astro]

Thanks for the reply, I must of slept on that detail...

 

[markmitch]

Anything left? I need the two rubber bumpers for the hood. I had installed hood pins but I am welding in the holes to go back to somewhat stock look and I must have tossed mine. Let me know. Thanks, Mark

 

[M_a_t_t]

Yeah. I haven't done anything with this van yet. I'll have to make sure it's got both of them.

 

[M_a_t_t]

Van wouldn't start so it'll have to be pulled around. Parts not involved in rolling are available now as well.

 

[bgoodjonny]

Hi
Is the AC condenser in tact?
Thanks

 

[M_a_t_t]

I believe so, I'd have to double check if the lines came off correctly or not.

 

[M_a_t_t]

I have it. I couldn't get one of the lines off so I cut the line. The condenser is uncut. The blower motor didn't work in the van so I have no idea if it works or hold pressure though.

 

[bgoodjonny]

I have it. I couldn't get one of the lines off so I cut the line. The condenser is uncut. The blower motor didn't work in the van so I have no idea if it works or hold pressure though.

That's great, none of the lines that are part of the condenser were cut, right? If the Evaporator Inlet Tube was cut that's ok. If you can post a picture, I can take a look but would like to get it from you. How much and can you ship to NJ? Thanks for pulling it out!