Chevy Astro and GMC Safari Forum banner
1 - 5 of 5 Posts

·
Registered
Joined
·
42 Posts
Discussion Starter · #1 ·
Most audio equipment dies for one simple reason. Most people push their equipment beyond its limits. Whether it is the amplifier, subwoofer or full range speakers, clipping is the number one cause of failure. To prevent clipping, use this tutorial.

To figure out what voltage you should set the gains to, multiply the RMS power of the amplifiers output by the impedance of the speaker, then find the square root of that number. If you are using an amplifier that has an RMS rating of more than your speaker(s) can handle/rated for, then use the RMS rating of the speaker (instead of the RMS of the amplifier) to determine the voltage to set your amp to. This is also referred to as gaining down.

Gain Setting Equation
Voltage of the output = sqrt(RMS Power X impedance of the speaker)
Example
Say the amp provides 100WRMS into a 4 ohm speaker:

Voltage = sqrt(100W X 4 ohms)
Voltage = sqrt(400W*ohms)
Voltage = 20V

Again, that was only an example, use the ratings of your amp to figure that out.
Setting the Gain(s)
To set the gain(s), you need two things:
1. A DMM (digital multi-meter) that is capable of measuring AC voltage (needs to be able to measure up to a range of 200V).
2. A test tone CD to use to set the gains at the correct setting.
Now, to set the gain(s):
1. Start the vehicle, and pop the test tone CD in the head unit.
2. DO NOT hook up the sub(s) or speaker(s) to the amplifier while doing this, just leave the outputs unused at this time.
3.Now, time to set up the head unit.
a. If the loudest you listen to your music at on a regular basis is 22/35 with bass @ +3 and treble @ 0 with MX (or any other sound processor) on, use those settings. NEVER turn the headunit above 3/4 of the maximum volume.
b. Remember to have the car turned on.
c. If you want to use bass boost on a sub amp, set it prior to setting the gains on the amp and use the center frequency of the bass boost (45 Hz for most amps) as your test tone.
d. Please remember that if you have a subwoofer volume control on the headunit, set it to full before you set the gains on the sub amp.
3. Take the leads from the DMM and but them on the outputs from the amp.
4. Set the gain so that the outputs of the amplifier equal the voltage you found above. This is a MUST.

Here is JL Audio tutorial on their site:
http://www.jlaudio.com/tutorials/Input_ ... ivity.html

And here is 20-80Hz test tones:
http://www.ronelmm.com/tones/

For test tones higher than 80Hz, download this program and you can create your own:
Adobe Audition Trial Version

It is best to use 50 Hz tone for a sub amp (unless you have bass boost, use the frequency that is boosted as the tone), and a 1kHz tone for a full-range amp.

This is a good way to set the gains, but if you have access to an oscilloscope, by all means use it. Then you can set the gains to their absolute maximum as you can see when the amplifier clips.

If you are wondering what exactly clipping is, and what it looks like, read this:
http://www.bcae1.com/2ltlpwr.htm

If you have any questions about this, post up, I'll try my best to answer them.

Also, remember a sub can only handle what it can, if you set the amp to its RMS you have to remember that the sub can handle only so much. It is box dependant, but it is best if you are not experienced to follow the manufacturers recommendations.

Enjoy, and remember to thump responsibly!
 

·
Registered
2000 Lifted 4x4 Astro 92 V8-350 Shorty
Joined
·
5,308 Posts
1low-stro said:
a. If the loudest you listen to your music at on a regular basis is 22/35 with bass @ +3 and treble @ 0 with MX (or any other sound processor) on, use those settings. NEVER turn the headunit above 3/4 of the maximum volume.
Sorry to say, this is where the OP completely blew it! Totally flawed logic.
Informative and good read otherwise.
I'll just leave it at that. :D
 

·
Administrator
Common Sense + Critical Thinking
Joined
·
12,417 Posts
It appears that it was just borrowed, word for word from 1 of about 2,674 forums dating back to 2005 or so.

Not that it's a bad thing, everything is built on or borrowed from someone that came before.
 
1 - 5 of 5 Posts
Top