Replacing Upper Ball Joint: what am I doing wrong?

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby chevymaher » March 20th 2017, 2:09am

How big is the open hole behind the one your working on. Since you cand man handle it yes drill more. Once you get a small hole through them they will loosen up.

Trust me everybody goes through this stuff. I am cussing every time I do something. Mr. Murphy is right there with you. I though i was going to be a hour screwing with my vans starter the other day. I found out I had to clean all the connections I was hours doing that.

Do you have access to t course file. Clean that top off some there may be some ragged edges of the pop rivet still hanging over the edge. Your getting there.

Just take some frustration out on it. Just beat the silly ball joint with the hammer while you cuss at it. My favorite is "Oh your coming out of there Beotch" Anyway as lumpy mentioned before the sharp blows and vibrations will help break things loose.

If you saw me going after a brake drum that had never been off before with a 5 lb hammer. You would think this guy has lost it. Rust just flying.

Chin up you will get it.
Image
User avatar
chevymaher
Team Leader
Team Leader
Firing on 8 Cylinders (L7)
Firing on 8 Cylinders (L7)
Years of Membership: chevymaher has been a member for 10 full yearschevymaher has been a member for 10 full yearschevymaher has been a member for 10 full yearschevymaher has been a member for 10 full yearschevymaher has been a member for 10 full yearschevymaher has been a member for 10 full yearschevymaher has been a member for 10 full yearschevymaher has been a member for 10 full yearschevymaher has been a member for 10 full yearschevymaher has been a member for 10 full years
Posts: 14281
Topics: 91
Images: 94
Joined: November 2010
Gender: Male
Alias (AKA): chevymaher
Van Model Year: 1994
Van Make/Model: GMC Safari
Extra Info: SLE RWD Mercruiser

  • Similar topics
    Replies
    Views
    Author

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby zach914v8 » March 20th 2017, 2:23am

X2 it sucks I know.... just keep at it and be positive, you will be very proud when you finish.
My Rides:

1974 Porsche 914 powered by a 305 Chevy v8.

1994 GMC Safari TBI 4.3, Lifted 4"
User avatar
zach914v8
Firing on 3 Cylinders (L1)
Firing on 3 Cylinders (L1)
Years of Membership: zach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full years
Posts: 320
Topics: 12
Images: 1
Joined: May 2009
Location: Houston, Texas
Gender: Male
Alias (AKA): ballzach
Van Make/Model: GMC Safari
Extra Info: 4 inch lift

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby Mmusicman » March 20th 2017, 3:20am

Lumpy wrote:
Big_kid wrote:It's been a long time since I separated a ball joint on an Astro- is it necessary to chain the spring?

I always do.
Image

You DO realize the spring can't go anywhere with a shock running thru it, don't you?
Plus... with the FULL weight of the vehicle on it, you couldn't pry is out if you wanted to. To get the spring out, you have to actually remove the shock, then keep lowering and finally pushing down on the lower arm.. until the spring "falls" out. I've done many.. it's quite basic.

On another note: We are up to 4 pages now.. and roughly two days (an entire weekend)... just how much is one ball-joint effort worth?
Image
2000 Astro LS 4x4 | NP233 | 31" LT265/70R17 Tires | 8" LIFT | 10" TOTAL
92 Chevy Astro Cargo Shorty | V8-350
http://www.CruisinSouthFlorida.com
User avatar
Mmusicman
V8 Swap Achievement
V8 Swap Achievement
Purple Status (L6)
Purple Status (L6)
Years of Membership: Mmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full years
Posts: 5097
Topics: 75
Images: 61
Joined: June 2013
Location: Ft. Lauderdale, Florida
Gender: Male
Alias (AKA): Scott
Van Model Year: 2000
Van Make/Model: Chevrolet Astro
Extra Info: 2000 4x4 - 92 V8-350

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby Astrodawn [OP] » March 20th 2017, 3:55am

chevymaher wrote:Just take some frustration out on it. Just beat the silly ball joint with the hammer while you cuss at it. My favorite is "Oh your coming out of there Beotch"


hahah, i've definitely started doing this. current research suggests that it helps.

thanks for the encouragement, y'all.

Mmusicman wrote:On another note: We are up to 4 pages now.. and roughly two days (an entire weekend)... just how much is one ball-joint effort worth?


roughly $200 + the immeasurable weight of giving up.

i figure even if i spend 20 hrs on this, i'm still getting "paid" $10/hr which is pretty damn good in my estimation.
Original Poster [OP]
Astrodawn
Firing on 2 Cylinders (L1)
Firing on 2 Cylinders (L1)
Years of Membership: Astrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full years
Posts: 275
Topics: 22
Joined: February 2017
Location: Washington, DC
Alias (AKA):
Van Model Year: 1998
Van Make/Model: Chevrolet Astro
Extra Info: RWD conversion

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby sadglad » March 20th 2017, 4:43am

I don't recall seeing any mention of the drill bits being used but they are not all created equal. Some bits sold at big box stores are junk, suitable for drilling wood and plastic only. They will get dull almost immediately drilling harder steel. If the package says "carbon alloy" or "carbon steel" or something similar then it's junk. You want something specifically labeled High Speed Steel or HSS for short. Something labeled cobalt is also good. That's HSS with cobalt added for extra toughness. Yes, they cost more but totally worth it.

The edges and corners on the tip of the bit should be completely crisp and sharp. It they are even slightly rounded they won't do the job. A good quality bit will be cutting out small chips or curls of metal continuously while drilling with moderate pressure. If you are not getting that then something is wrong. Some kind of lube oil helps a lot. Real cutting oil is nice but 3in1 or any oil is better than nothing.

Really top quality bits are expensive. I did my ball joints with Irwin bits like these. Reasonable price and widely available, Lowes etc.
Attachments
IMG_2818.JPG
sadglad
Site Contributor
Site Contributor
Firing on 3 Cylinders (L1)
Firing on 3 Cylinders (L1)
Years of Membership: sadglad has been a member for 9 full yearssadglad has been a member for 9 full yearssadglad has been a member for 9 full yearssadglad has been a member for 9 full yearssadglad has been a member for 9 full yearssadglad has been a member for 9 full yearssadglad has been a member for 9 full yearssadglad has been a member for 9 full yearssadglad has been a member for 9 full years
Posts: 336
Topics: 22
Images: 15
Joined: January 2012
Gender: Male
Alias (AKA):
Van Model Year: 2002
Van Make/Model: Chevrolet Astro
Extra Info: 2002 AWD Cargo

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby Astrodawn [OP] » March 20th 2017, 5:19am

thanks for the info! i honestly don't know what sort of drill bits i'm using, cause my friend just dropped them off with the drill. but, i'll be buying some replacement ones for him, so it's good to know about quality.
Original Poster [OP]
Astrodawn
Firing on 2 Cylinders (L1)
Firing on 2 Cylinders (L1)
Years of Membership: Astrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full years
Posts: 275
Topics: 22
Joined: February 2017
Location: Washington, DC
Alias (AKA):
Van Model Year: 1998
Van Make/Model: Chevrolet Astro
Extra Info: RWD conversion

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby Rockridge » March 20th 2017, 11:50am

drilling all the way through will help, as does heat but you probably don't want to go buy a torch, but shouldn't need to anyway. WD-40 or PB Blaster to cool the drill bit and get things moving.

like Lumpy says. lots of moderate repeated strikes will work versus trying to get it in one shot.

Support the control arm with something like a block of wood so that all the hammer energy goes into the rivet.

keep the faith!
Rockridge
Firing on 8 Cylinders (L1)
Firing on 8 Cylinders (L1)
Years of Membership: Rockridge has been a member for 5 full yearsRockridge has been a member for 5 full yearsRockridge has been a member for 5 full yearsRockridge has been a member for 5 full yearsRockridge has been a member for 5 full years
Posts: 949
Topics: 53
Images: 0
Joined: May 2016
Location: New Hampshire
Gender: Male
Alias (AKA): Walker
Van Model Year: 2004
Van Make/Model: Chevrolet Astro
Extra Info: LS AWD

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby Big_kid » March 20th 2017, 1:26pm

This was on my daughter's BF's truck exactly as you see it. Just keeping safety a priority.

68450
95 Astro Conversion of unknown irrelevant lineage
We have enough youth. How about a fountain of smart?
User avatar
Big_kid
Team Leader
Team Leader
Firing on 8 Cylinders (L7)
Firing on 8 Cylinders (L7)
Years of Membership: Big_kid has been a member for 13 full yearsBig_kid has been a member for 13 full yearsBig_kid has been a member for 13 full yearsBig_kid has been a member for 13 full yearsBig_kid has been a member for 13 full yearsBig_kid has been a member for 13 full yearsBig_kid has been a member for 13 full yearsBig_kid has been a member for 13 full yearsBig_kid has been a member for 13 full yearsBig_kid has been a member for 13 full yearsBig_kid has been a member for 13 full yearsBig_kid has been a member for 13 full yearsBig_kid has been a member for 13 full years
Posts: 6871
Topics: 185
Images: 357
Joined: June 2008
Gender: Male
Alias (AKA):
Van Model Year: 1995
Van Make/Model: Chevrolet Astro
Extra Info: 2WD 5.7 V8

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby Lumpy » March 20th 2017, 2:37pm

Mmusicman wrote:
[chaining the coils]

You DO realize the spring can't go anywhere with a shock running thru it, don't you?
Plus... with the FULL weight of the vehicle on it, you couldn't pry is out if you wanted to. To get the spring out, you have to actually remove the shock, then keep lowering and finally pushing down on the lower arm.. until the spring "falls" out. I've done many.. it's quite basic.



Shock is disconnected. There's energy in mine. Mine certainly don't "fall out" as I've heard some describe. The coil spring tension suddenly released when I break the top BJ loose is immense. Throws the LCA downward very violently (moves the van up on it's jack stands). Much farther than the shock length would allow. Stressing the shock by bumping it past it's extension limit doesn't seem like something I'd want to do.

Even if they were completely relaxed, a 30 lb spring falling onto my shin underneath it, even without stored up spring energy, OUCH!


I also put the removed wheel and tire under the rocker panel of the side I'm working on. Then if all my banging and prying should bump the van off it's jacks, the wheel/tire under the rocker will keep it off ME.


Lots of prying and banging going on over there in the corner of the box. Ptolemy could move planets with all that leverage in mine.


Lump
User avatar
Lumpy
Deprived Privileges
Deprived Privileges
Firing on 8 Cylinders (L7)
Firing on 8 Cylinders (L7)
Years of Membership: Lumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full years
Posts: 10996
Topics: 261
Joined: April 2010
Location: Phoenix AZ USA
Gender: Male
Alias (AKA):
Van Model Year: 1989
Van Make/Model: Chevrolet Astro
Extra Info: 11 in. lift Camo

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby sixsixsixsix is online! » March 20th 2017, 4:24pm

Mike here in N. Ky. - was wondering... do you still have the wheel on? If so, just wondering why?
Can you back away a little when you take your next photo so we can see your working area.

And do you have a male ( or female ) mechanic friend w/ some, shall we say... heft, that can use a drill and bits properly, swing a 5 lb sledge or use a HD Prybar/Cold Chisel?

Do We need to come down there or what?



Mike

PS: AGAIN ( LOL ) Her van - AWD - NO SPRINGS - Torsion Bars instead.
Last edited by sixsixsixsix is online! on March 20th 2017, 5:53pm, edited 2 times in total.
.
"1 Nautilus died, BLM spawned, Antifa runs amok
- CRT & unions have taken schools by storm
THEN:
Not a single "Black" "Leader" condemns Black Crime
- White Supremacists get blamed for it all - they sure do get around"
User avatar
sixsixsixsix is online!
Purple Status (L6)
Purple Status (L6)
Years of Membership: sixsix has been a member for 7 full yearssixsix has been a member for 7 full yearssixsix has been a member for 7 full yearssixsix has been a member for 7 full yearssixsix has been a member for 7 full yearssixsix has been a member for 7 full yearssixsix has been a member for 7 full years
Posts: 5054
Topics: 39
Images: 1411
Joined: May 2014
Location: Edgewood, Northern Ky.
Gender: Male
Alias (AKA): Mike
Van Model Year: 1992
Van Make/Model: Chevrolet Astro
Extra Info: LT W CPI - RWD 200K

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby 1lowcab » March 20th 2017, 4:38pm

I also put the removed wheel and tire under the rocker panel of the side I'm working on. Then if all my banging and prying should bump the van off it's jacks, the wheel/tire under the rocker will keep it off ME.


Ditto

I can't see any movement on these rivets. And I'm worried I'm breaking something else with all the force I'm applying



Sounds like it's time for the smoke wrench, get'er nice and hot then smack it. :o
User avatar
1lowcab
Firing on 8 Cylinders (L3)
Firing on 8 Cylinders (L3)
Years of Membership: 1lowcab has been a member for 5 full years1lowcab has been a member for 5 full years1lowcab has been a member for 5 full years1lowcab has been a member for 5 full years1lowcab has been a member for 5 full years
Posts: 2948
Topics: 58
Images: 165
Joined: April 2016
Location: OH
Gender: Male
Alias (AKA):

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby WimpTech » March 20th 2017, 5:14pm

VERY proud of you Dawn, don't take any $hit from that [email protected]$#%^ ball joint... SHOW IT who's da BOSS!
WimpTech - Precision Guesswork... Questionable Results.

My Van Build: viewtopic.php?f=127&t=103714
My Other Van: http://www.vcvc.org/showthread.php/3013 ... ersion-Van
User avatar
WimpTech
Firing on 4 Cylinders (L5)
Firing on 4 Cylinders (L5)
Years of Membership: WimpTech has been a member for 5 full yearsWimpTech has been a member for 5 full yearsWimpTech has been a member for 5 full yearsWimpTech has been a member for 5 full yearsWimpTech has been a member for 5 full years
Posts: 4419
Topics: 39
Images: 322
Joined: January 2016
Location: Texas!
Alias (AKA): =Wimpy=
Van Model Year: 2000
Van Make/Model: GMC Safari
Extra Info: Retired

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby Lumpy » March 20th 2017, 6:17pm

Wimpazz wrote:
VERY proud of you Dawn...



I sure am.

She's getting the job done with the tools at hand. I don't think it's job that could be done easier by "A Man". It's not a strength issue. And I don't think she's using a tool incorrectly. I've sacrificed a wood chisel to get something metal to move. I HAVE a dedicated sacrificial wood chisel that I use all the time on the "wrong" material. I use dedicated screwdrivers as pry/chisel tools all the time. My first drill was a right angle attachment on a 1/4" (no larger) drill with an AC power cord (no cordless). The theoretically proper way to drill hard steel IS on low speed. Although I often violate that for speed, losing the bit in the process.

Bottom line is we have a ball joint. Not that we "could have used a different tool".


Lump
User avatar
Lumpy
Deprived Privileges
Deprived Privileges
Firing on 8 Cylinders (L7)
Firing on 8 Cylinders (L7)
Years of Membership: Lumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full years
Posts: 10996
Topics: 261
Joined: April 2010
Location: Phoenix AZ USA
Gender: Male
Alias (AKA):
Van Model Year: 1989
Van Make/Model: Chevrolet Astro
Extra Info: 11 in. lift Camo

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby Mmusicman » March 20th 2017, 6:38pm

Lumpy wrote:The coil spring tension suddenly released when I break the top BJ loose is immense. Throws the LCA downward very violently..

I guess we do them differently somehow.. (although your photo suggests we do them somewhat similar to start). You obviously must be removing the jack durring BJ separation... where as I keep it in place supporting the weight.

Even in your photo... there is absolutely NO WAY the spring could come out.
But I'd ALSO like to state for the record that it's never wrong to play it safe and have extra safety measures in place... especially if they way you do it causes violent release.

I ALWAYS support the lower control arm with a jack... with the frame sitting on jack-stands (there is a perfect place made for it underneath near the doors). When I break EITHER ball-joint loose, there is NO motion whatsoever, other than slight separation (I always leave the nut threaded toward the end as extra precaution. Once BJ separates, then I simply continue to lower the control arm gently (with floor jack) until the spring is completely unloaded and it stops on it's own. Even with the lower control arm fully lowered and spring unloaded, I still have to apply some minimal additional downward pressure to get spring to clear all the obstacles and fall out, particularly the cavity it sits in. A broken shock would STILL not allow it to come out.

Another note: when I am finally lowering the control arm to unload the spring... I'm doing it from the front of the vehicle. The spring can only come out from the side... away from the angled control arm.

Not sure why or how our experiences are so different.. but I have no surprises or unexpected issues. I guess next time I will have to make a video of my spring easily falling out unloaded the way I do them. As far as the upper control arm... there is NO pressure whatsoever, but again I always support the vehicle directly underneath the lower control arm when dealing with ball-joints, so it remains supported and loaded... compressed by the vehicle's weight.

This "side-discussion" is regarding coils on RWD vans... and yes the OP is driving an AWD with torsion bars. I would still treat it the same way.. be sure to have a jack or jack stand under the lower control arm while separating the ball joints. Do NOT allow it to hang freely which will MOST CERTAINLY "explode with motion" when it is freed and uncoupled from the rest of the suspension.

In this photo, it is shown the spring "can" be removed with the shock in place, but it must be disconnected from control arm to do so. Left hanging in place (even disconnect on one end), it is a slight obstacle. The biggest issue (with shock in place) is positioning the spring back in place against an angled surface and making sure it is seated properly at the top. This is where it could come out, trying to wedge it back in place. I use my camera phone for inspection (from inside the spring view) to see it is centered properly, but can't do so if the shock is in the way.
20170102_132725a.jpg

Here you can see the dedicated jack point (further back) that most of us are probably well aware of..
20170102_143435a.jpg
Image
2000 Astro LS 4x4 | NP233 | 31" LT265/70R17 Tires | 8" LIFT | 10" TOTAL
92 Chevy Astro Cargo Shorty | V8-350
http://www.CruisinSouthFlorida.com
User avatar
Mmusicman
V8 Swap Achievement
V8 Swap Achievement
Purple Status (L6)
Purple Status (L6)
Years of Membership: Mmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full yearsMmusicman has been a member for 8 full years
Posts: 5097
Topics: 75
Images: 61
Joined: June 2013
Location: Ft. Lauderdale, Florida
Gender: Male
Alias (AKA): Scott
Van Model Year: 2000
Van Make/Model: Chevrolet Astro
Extra Info: 2000 4x4 - 92 V8-350

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby nonhog » March 20th 2017, 7:58pm

Hope its going well and you are done. :)
Are you going to do the other side also? Reason I ask is maybe you could pick up a HF grinder and make short work out of getting a flat spot to drill. Would lower the time needed by a bunch. http://www.harborfreight.com/power-tool ... 69645.html
On sale for 9.99 frequently. Just a thought.


Another thing that helps me is lying to myself. After a break from a frustrating job, I don't dwell on the time I already spent, I tell myself I am just starting. Sometimes several times. :) Works for me.
Recovering hoarder
My Slow build..... viewtopic.php?f=127&t=107426
User avatar
nonhog
Firing on 7 Cylinders (L1)
Firing on 7 Cylinders (L1)
Years of Membership: nonhog has been a member for 4 full yearsnonhog has been a member for 4 full yearsnonhog has been a member for 4 full yearsnonhog has been a member for 4 full years
Posts: 743
Topics: 37
Images: 16
Joined: November 2016
Location: Tacoma (ish)
Gender: Male
Alias (AKA):
Van Model Year: 1996
Van Make/Model: GMC Safari
Extra Info: AWD

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby zach914v8 » March 20th 2017, 8:24pm

X2 on this, I have been working on cars professionally for many years, sometime they still get the best of me too. When that happens I work on something else for a bit, or if it's real bad I will go and take a walk to clear my head. Don't give up! You can do this and it must get done. own it.
My Rides:

1974 Porsche 914 powered by a 305 Chevy v8.

1994 GMC Safari TBI 4.3, Lifted 4"
User avatar
zach914v8
Firing on 3 Cylinders (L1)
Firing on 3 Cylinders (L1)
Years of Membership: zach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full yearszach914v8 has been a member for 12 full years
Posts: 320
Topics: 12
Images: 1
Joined: May 2009
Location: Houston, Texas
Gender: Male
Alias (AKA): ballzach
Van Make/Model: GMC Safari
Extra Info: 4 inch lift

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby Astrodawn [OP] » March 20th 2017, 10:03pm

Not quite done. It was raining earlier and I don't have a garage.

I've started drilling. Sent my roommate to the store to see if she could find a file of some sort. Anyone know what type?

I'm just trying to drill through these rivets. Come hell or high water.
Original Poster [OP]
Astrodawn
Firing on 2 Cylinders (L1)
Firing on 2 Cylinders (L1)
Years of Membership: Astrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full years
Posts: 275
Topics: 22
Joined: February 2017
Location: Washington, DC
Alias (AKA):
Van Model Year: 1998
Van Make/Model: Chevrolet Astro
Extra Info: RWD conversion

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby AstroWill » March 20th 2017, 10:07pm


Trolls take away from productive work, best to ignore & go about your business. See: Dark Tetrad
Report terrorists and anyone inciting violence to FBI @ fbi.gov and 800-CALLFBI (225-5324)
User avatar
AstroWill
Technical Director
Technical Director
Firing on 8 Cylinders (L7)
Firing on 8 Cylinders (L7)
Years of Membership: AstroWill has been a member for 12 full yearsAstroWill has been a member for 12 full yearsAstroWill has been a member for 12 full yearsAstroWill has been a member for 12 full yearsAstroWill has been a member for 12 full yearsAstroWill has been a member for 12 full yearsAstroWill has been a member for 12 full yearsAstroWill has been a member for 12 full yearsAstroWill has been a member for 12 full yearsAstroWill has been a member for 12 full yearsAstroWill has been a member for 12 full yearsAstroWill has been a member for 12 full years
Posts: 12020
Topics: 109
Images: 484
Joined: February 2009
Alias (AKA): Critical Thinking+Common Sense
Van Make/Model: Chevrolet Astro
Extra Info: I love peaches

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby Lumpy » March 20th 2017, 10:25pm

Mmusicman wrote:
...I guess next time I will have to make a video of my spring easily falling out unloaded the way I do them...



Not for me you don't. Yours don't, mine do. That simple.


Lump
User avatar
Lumpy
Deprived Privileges
Deprived Privileges
Firing on 8 Cylinders (L7)
Firing on 8 Cylinders (L7)
Years of Membership: Lumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full yearsLumpy has been a member for 11 full years
Posts: 10996
Topics: 261
Joined: April 2010
Location: Phoenix AZ USA
Gender: Male
Alias (AKA):
Van Model Year: 1989
Van Make/Model: Chevrolet Astro
Extra Info: 11 in. lift Camo

Re: Replacing Upper Ball Joint: what am I doing wrong?

Postby Astrodawn [OP] » March 20th 2017, 10:42pm

I drilled. A hole. Through the rivet.

And then promptly got one of the pin punches stuck in said hole.

@#[email protected]&#+$&
Original Poster [OP]
Astrodawn
Firing on 2 Cylinders (L1)
Firing on 2 Cylinders (L1)
Years of Membership: Astrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full yearsAstrodawn has been a member for 4 full years
Posts: 275
Topics: 22
Joined: February 2017
Location: Washington, DC
Alias (AKA):
Van Model Year: 1998
Van Make/Model: Chevrolet Astro
Extra Info: RWD conversion

PreviousNext

 
  • Related topics
    Replies
    Views
    Last post

Return to Stock Suspension

It is currently July 23rd 2021, 8:19pm

Stock Suspension Forum
Stock SuspensionStock Suspension, Factory Suspension, Unmodified, Standard.
Moderator: chevy57bert
To create a new topic in Stock Suspension, click this button:
Previous topic Next topic
Recent Image Attachments
Views: 155
Comments: 7
Date: Jul 19 '21
Time: 6:17am
» Read last comment
Views: 195
Comments: 6
Date: Jul 07 '21
Time: 2:54pm
» Read last comment
Attached by:
stal023
in Stock Suspension
Views: 400
Comments: 11
Date: Jun 24 '21
Time: 7:00pm
» Read last comment
Attached by:
Attached by: Mmusicman
Mmusicman
in Stock Suspension
Views: 463
Comments: 9
Date: May 12 '21
Time: 2:43pm
» Read last comment
Attached by:
baily144
in Stock Suspension
Views: 494
Comments: 10
Date: May 03 '21
Time: 9:08pm
» Read last comment
Sponsors

Who is online

Users browsing this forum: No registered users and 14 guests